Will Flex Wrap Tape Work On Fishing Eyes To Repair Them?

Download Article

Mod fishing rods don't suspension hands, but they can be stock-still hands with a few elementary tools you may take at home. If your rod snapped, you can mend it together with a fiberglass pole and epoxy to hide the pause. When one of the guides breaks, you can remove it and wrap a new one in its place. Y'all can change rod tips if they snap or break equally well. With a petty flake of piece of work, you can gear up your rod so it's equally adept equally new!

1
Sand or cut the broken ends of the rod and so they're flush. Use 180- or 220-dust sandpaper to smooth the ends then they fit together easily if the rod has a clean break. If your angling rod has a jagged edge, then use a pair of scissors to cutting the abrupt edges off of the end of the rod and so the pieces are flush. After you brand your cutting, use sandpaper to polish out the edges and roughen upwards the surface.^[i]
- Jagged edges are weaker and are more likely to pause once again than edges that are flush with 1 another.
two
Measure the circumference of the rod. Employ a flexible tape measure and wrap it around the broken cease of your fishing rod. So measure the circumference on the other piece of your angling rod to see if it'southward skinnier. Write downwards your measurements so you know what pole size you lot need for fixing your rod.^[2]
- You can besides mensurate the diameter of the rod on both of the broken ends if you don't accept a flexible measuring tape.
Advertisement
3
Cut a piece of fiberglass pole and then it's about 12 in (thirty cm) long. Get a fiberglass pole that has a circumference that's about ⁱ⁄_viii – ^one⁄₄ inch (0.32–0.64 cm) smaller than your fishing rod. Employ a hacksaw to cut out a 12 in (30 cm) section of the pole then it can fit inside your fishing rod and support the rod without breaking.^[3]
- You tin buy fiberglass poles from your local hardware store. Information technology doesn't matter what colour yous use since information technology volition fit within of the rod.
- If your fishing rod isn't hollow, then using a fiberglass pole won't piece of work. Yous tin can either endeavor to tape your rod back together or get a new one.
Tip: You can also cut a section off of an old fishing pole that you don't use anymore if you lot don't accept a fiberglass rod.
4
Slide the fiberglass pole into one side of the fishing rod. Hold your rod horizontally and so y'all can position the fiberglass pole in the rod without it sliding too far. Push i cease of the fiberglass pole into the end of the rod with the handle. Go on sliding the pole into the fishing rod until in that location'due south vi inches (xv cm) sticking out from the end.^[4]
- If the pole doesn't fit snugly inside the angling rod, then wrap the pole with duct or masking record to make it thicker.
v
Apply two-part epoxy to the exposed side of the fiberglass pole. Open your 2-part epoxy and pour it into a basin. Use a paintbrush to spread a sparse layer of the epoxy on the exposed end of the fiberglass pole. Once the 2-part epoxy is mixed, piece of work quickly and then information technology doesn't dry or ready before you lot put your rod back together.^[5]
- You can buy 2-function epoxy from any hardware or craft store.
half dozen
Slide the other part of the rod onto the fiberglass and let it dry. Slowly push the other end of your rod onto the exposed end of the fiberglass pole. Brand sure the guides on the pole line up with one another so your line doesn't get tangled when yous effort using your pole again. Push the 2 pieces of the rod together so they're flush. Let the epoxy fix overnight so information technology firmly adheres to the rod.^{[half dozen]}
- The epoxy doesn't set correct away, so you tin nevertheless rotate or move the rod pieces in one case you slide them together.
- If whatsoever epoxy comes out of the articulation while yous're sliding the pieces together, wet your finger and smooth out the epoxy so it isn't equally visible.
- Wrap a layer of electric tape effectually the seam if you want an additional layer of security.
Advertising

1
Cut the tape or thread around the broken guide with a razor blade. Use a straight razor bract or a arts and crafts knife to remove any threading that may be surrounding the rod guide. If it's difficult to remove using just a blade, then try heating the area for 3-4 seconds with a lighter to loosen whatsoever of the adhesives. Peel off the record and unwind the threading until the quondam, broken guide comes off of the rod.^[7]
- Rod guides are the circular metal pieces along the length of the rod that help keep your line direct.
- Be careful not to heat the rod for too long since information technology could cause damage to it.
- Don't cut into the rod with your razor, or else you could damage information technology and make information technology weaker.
2
Sand the rod and foot of the new guide to get better adhesion. Use 120- or 220-dust sandpaper to go rid of any leftover adhesive and to add molar to the rod. Rub all the way around the rod on the spot where you desire to identify the new guide. Then, use your sandpaper on the foot of the guide, which is the flat function that rests against the fishing rod.^[viii]
- Yous can buy new fishing guides at sporting good stores. Make certain the new guide is the same size and manner equally the other guides on your fishing rod or else your line may snag or get tangled.
iii
Tape the new guide onto the rod so it's aligned. Press the human foot of the new guide onto the rod then it's in line with the other guides. Rip off a thin piece of masking tape and wrap it around the foot then it'due south held in identify. That way, yous don't demand to continue holding information technology in identify while yous wrap it.^[ix]
- You tin can also use super mucilage, but it will exist hard to move or readjust one time the glue is set.
4
Wrap the foot of the guide with thread to concur it in place. Any type of thread will work for wrapping your guide onto the rod. Loop your threading effectually the rod so it'south ⁱ⁄₂ – ³⁄₄ inch (ane.3–i.9 cm) from the guide's pes on the side closest to the handle. Maintain tension on the loop and start tightly winding the thread around the rod. Make sure the thread doesn't overlap with loops you've already made and that they are flush with one another.^[x]
- Take the piece of tape off of the foot yous've wrapped everything beneath it.
Tip: Use a thread that matches the color of your rod if you desire information technology to blend in.
5
Identify a looped slice of thread over the wrap when there's ¹⁄₈ in (0.32 cm) left. When your wrapping is ¹⁄_eight inch (0.32 cm) from the circular office of the guide, stop winding the thread around the pole. Cutting a separate piece of thread so information technology's about vi inches (15 cm) long and fold it in half to form a loop. Lay the 2nd piece of thread on top of your wrapping so the loop sticks out about your guide.^[xi]
- If you don't have any other thread, you can besides use a thin fishing line instead.
6

Wrap the terminal ^ane⁄₈ in (0.32 cm) over the 2d piece of thread. Once the looped piece of thread is on top of the wrapping, continue spinning your thread around the pes of the guide. Continue wrapping the concluding ^one⁄₈ inch (0.32 cm) of the guide so the heart of the looped piece is held against the rod.^[12]
seven
Feed the thread through the looped piece and pull it tight. Once you reach the end of your wrapping, cut the terminate of the thread you lot used to wrap and pull it through the middle of the loop. Pull the other terminate of the looped piece down and away from the guide to pull the thread underneath the wrapping. This way, the wrapping is secured to the rod without having to tie a knot.^[13]
- If you don't want to utilise a looped piece of thread, you tin can also try tying a knot in the threading, simply it may not be as strong and information technology could exist more difficult.
8
Pigment two-part epoxy onto the thread and let it dry. Mix the 2 parts of the epoxy in a small dish with a paintbrush until they are thoroughly combined. Paint a thin layer of the epoxy over your threading so it hardens and stays in place. Go on the rod horizontal and allow it dry overnight before y'all try using your rod once again.^[14]
- Work quickly with the epoxy since information technology will quickly start to dry and harden once you mix it.
Advertisement

one
Estrus the tip top of your fishing rod with a lighter to loosen the adhesive. Set the rod horizontal and then y'all tin easily reach the tip. Concord a lighter underneath the tip top of the rod, which is the ringed piece at the end of the rod, and heat it up for 4-5 seconds at a time. Once it's heated, try pulling it off with a pair of pliers or past mitt. If it doesn't come off easily, try heating information technology for another few seconds.^[15]
- Heating the tip top helps loosen the adhesive holding it in place and so information technology's easier to remove.
- If the tip snapped off of your rod, then you tin remove the old tip top from the broken slice or you tin can skip this step.
2

Smooth the tip of the rod with sandpaper to remove any shards. Rub the exposed tip of the rod with 120- or 220-dust sandpaper to smooth it out. Rotate the rod around the sandpaper until the tip is smooth and flush. It's okay if there are small-scale abrasion marks on the rod tip since it will have better adhesion to the new tip top.^[16]

Tip: If sandpaper isn't enough to remove the shards on the end of your line-fishing rod, then carefully cut off the ends with a pair of scissors.
3
Cut pieces of rod cement into strips that fit inside your new tip top. Rod cement is an agglutinative that comes in a solid block and is used for line-fishing rods to hold guides and tips in place. Employ a razor or craft knife to cut out modest strips of the rod cement and then they fit inside the hollow bedchamber on your rod tip peak.^[17]
- You lot can purchase rod cement and new tip tops from your local sporting goods store or online.
iv

Cook the rod cement inside the tip top with your lighter. Agree the new tip acme with a pair of pliers and put the pieces of rod cement in the hollow tube at the end of information technology. Use your lighter to rut the rod cement for 4-v seconds and melt it so y'all can attach information technology to your rod. In one case the rod cement is melted, piece of work quickly so information technology doesn't solidify once more.^[18]
5
Slide the tip height onto your rod and so it lines up with the guides and let it dry. While the cement is nevertheless hot, slide it onto the tip of your rod and rotate it so the ring is in line with the other guides. Wipe away any excess rod cement with a piece of paper towel and let it prepare for at least one-2 hours. Once the cement is dry out, your rod is fix to use!^[19]
- If you need to accommodate or reposition the tip top afterward the cement is dry, then heat it once again for iii-4 seconds with your lighter.
Advertizement

Add New Question

Question

Where do I buy epoxy resin glue?

At any dwelling house improvement or hardware store.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advert

Take your rod to a fishing supply store or a repair person if yous have trouble fixing it on your ain.
If you need to set a snapped rod in an emergency, overlap the pieces past 6 inches (xv cm) and record them together tightly.^[xx]

Thanks for submitting a tip for review!

Don't hold a flame against your rod longer than a few seconds or else you could permanently damage the rod.
Be conscientious while working with razor blades so yous don't accidentally cut yourself.

Advertizing

Things You'll Need

Pair of scissors
Sandpaper
Tape mensurate
Fiberglass pole
Hacksaw
2-part epoxy
Bowl
Paintbrush
Electric tape (optional)

Razor blade
Lighter
Sandpaper
Masking tape
Rod guides
Thread
ii-office epoxy
Dish
Paintbrush

Lighter
Pliers
Sandpaper
Rod cement
Craft pocketknife
Rod tip elevation

Almost This Article

Article Summary X

To fix a snapped angling rod, endeavour using a fiberglass pole and some epoxy. Outset, sand the snapped edges to brand them flush. Smooth edges are stronger and less probable to intermission. Cut a 12 inch long piece of fiberglass pole using a hacksaw. Slide ane end of the pole into your line-fishing rod until there are 6 inches sticking out. One time the fiberglass pole fits snugly into the rod, apply epoxy to the exposed stop using a paintbrush. Connect the second one-half of the broken rod to the fiberglass pole and let the epoxy set. To replace the rod guide, start, remove whatever threading from around the guide using a craft knife. Align the new guide onto the rod and use tape to hold it in identify. Wrap the new thread over the guide and and so cover it in epoxy to set up information technology. For more ideas on fixing a cleaved fishing rod, like how to change a rod tip, read on.

Did this summary help y'all?

Thanks to all authors for creating a page that has been read 209,735 times.

Did this commodity help you?